Testing and specification of drymix mortar

Also note what the slump looks like; true similar shape to the coneshear the slump has sheared in some waycollapse no resemblance to the original cone.

Testing and specification of drymix mortar

Product Details

A number in parentheses indicates the year of last reapproval. Summary of Test Method 1. No other units of measurement are included in this standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are Testing and specification of drymix mortar and may cause chemical burns to skin and tissue upon prolonged exposure.

The mortar or plaster is then subjected to a controlled vacuum suction for 60 s, after which the flow is again determined. The water retention is the final flow divided by the initial flow expressed as a percentage. Significance and Use 4. Test results may be used to determine compliance with specifications.

This is also true when a plaster is applied as a coating on masonry units. Current edition approved Feb. Originally approved in Last previous edition approved in as C — The stopcock and the bore of the tubing shall be at least 4-mm.

A check valve or water trap, or both, is suggested for the connection to the vacuum source. The length of the tubing projecting into the 1-L flask from the stopcock shall extend at least 25 mm below the center line of the vacuum connection. The contact surfaces of the funnel and perforated dish shall be plane and may need to be lapped to ensure intimate contact.

An airtight seal shall be maintained stopcock to a vacuum flask, to which a controlled vacuum is applied. The perforated dish shall be made of metal not attacked by masonry mortar or plaster Note 1.

The metal base of the dish shall have a thickness of 2. The stopcock bore shall have a 4. Tamp 15 times with the tamper. Apply ten of the tamping strokes at approximately uniform spacing adjacent to the rim of the dish, and with the long axis of the tamping face held at right angles to the radius of the dish.

Apply the remaining five tamping strokes at random points distributed over the central area of the dish. Use just enough tamping pressure to fill the dish with the top of the material extending slightly above the rim. Smooth off the material by drawing the flat side of the straightedge with the leading edge slightly raised across the top of the dish.

Strike-off the material to a plane surface flush with the rim of the dish with the straightedge held in a perpendicular position; using a sawing motion, draw the straightedge across half of the surface of the dish; repeat the procedure on the other half of the unfinished surface.

If the material is pulled away from the side of the dish during the process of drawing the straightedge across the dish, gently press the material back into contact with the side of the dish using the tamper.

ASTM C 387 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete

Complete the entire filling and strike-off operation in not more than 2 min. This shall be accomplished by either of the following procedures. Care shall be taken to ensure that none of the holes in the perforated dish become clogged.

Testing and specification of drymix mortar

Hardened, smooth, not rapid filter paper shall be used. It shall be mm in diameter and be placed so as to completely cover the perforations in the dish. NOTE 1—Stainless steel, brass, and bronze are suitable metals for this purpose.

CEMEX dry silo mortar complies with the requirements of: BS EN ‘Specification for mortar for masonry, Masonry Mortar’ which replaced the following mortar and test method standards from the 31st Jan BS , ‘Methods of testing mortars, screeds and plasters, Physical Testing’ ‘Specification for dry packaged. the test specimens are demolded. and for a minimum of 30 min in the case of 3-in mm (No. shall be a prism two approximately equal layers in accordance with the general of 4-in. it is not permitted.3 Mortar—Mix mortar in a mechanical mixer as described moist curing schedule shall be extended. We are leading suppliers and manufacturers of Mortar Mixer. It is used for mixing cement pastes, mortars and pozzolans. The mixer consists of an epicyclic type stainless steel paddle imparting both planetary and revolving motion.

Connection is made between the vacuum flask and the vacuum gage. After suction for 60 s, quickly turn the stopcock to expose the funnel to atmospheric pressure.

NOTE 2—Vacuum values are all given as pressure relative to atmospheric pressure. NOTE 3—Gages reading pressure in other units are acceptable as long as their capacity and scale increments comply with the levels specified here.

For example, a vacuum gage with a minimum capacity of 70 mm of Hg in 1-mm increments is acceptable.

ASTM C Packaged, Dry, Combined Materials for Concrete | CTLGroup

To convert mm of Hg to kPa, multiply by 0. Set the dish on a work table, plow and mix the mortar or plaster for 15 s, with the rubber scraper prescribed in Practice Cspecification of BS/EN/DIN/ASTM standards.

1 COMPANY PROFILE fully equipped testing laboratory will work round the clock ensuring the quality. Qatar Plaster (QP) will be assuring the quality of products by strict quality control measures starting from the Dry mix mortar for concrete and masonry repairs. Consists of OPC, quality.

ASTM C, “Standard Specification for Preblended Dry Mortar Mix for Unit Masonry” TEST METHODS: ASTM C, “Standard Test Method for Compressive Strength of. American Petroleum Institute Purchasing Guidelines Handbook API ® Monogram ® Equipment API Specification 13A 18th Edition, August Specification for Drilling Fluids – Specifications and Testing Specification for Drilling Fluids – Specifications and Testing Table of Contents General Evaluation Base Clay Drymix Mortar;.

Field testing of masonry mortar should be performed in accordance to ASTM C Test Method - Mortar Aggregate Ratio. Specification of ASTM C “Mortar Unit Masonry” when tested in accordance of the prescribed testing protocols in ASTM C, SUPER ’N’ SAND MORTAR MIX. SPEC MIXª Core Fill Grout is a dry, preblended mix containing cementitious materials and dried aggregates.

It is formulated to provide bulk bags of mortar to the project site, the portable silo is loaded, using a jobsite forklift, • ASTM C Standard Specification for Grout for Masonry • ASTM C Standard Specification for. Experienced masons know that the procedures for how to mix mortar with colors (or pigments) is a precise science of combining mortar mix, cement, pigment and water in the right proportions.

A Simple Guide to Concrete Cube Testing